Savant

Content

About

Version DOR-xxx-xx

Version SIS-5000

Used Symbols

About

Savant is a recognized leader in home control and automation, and one of the fastest-growing Smart Home companies in the luxury and mid-market. Savant´s powerful technology brings the four pillars of automation (climate, lighting, entertainment and security) together in a single application interface for the homeowner. This comprehensive whole-home control, termed the Single App Home, delivers the premium experience in all of Home Automation and is offered through iOS and/or Android.

https://www.savant.com/

Savant Version 2N IP Intercom version Video in call Audio in call Switch control
DOR-xxx-xx 2.21.3.30.6 (tick) (tick) (tick)
SIS-5000 2.9.0 (tick) (tick) (tick)

Version DOR-xxx-xx

2N IP Intercom Settings

  Requirements for 2N IP Intercom

To Connect and configure a 2N Door Station do the following: Find IP Address of the Door Station. Either use a any network scanning software or the 2N Network
Scanner. Open a web browser. Enter the Door Stations IP Address in the web browsers address bar. Enter Username and Password for the Door Station. The defaut username / password of 2N units is: Username: admin, Password: 2n.

In a web browser log in to the Door Station to be configured. Select Services.
Select Phone > Calls. Set Incoming Calls to Automatic for both SIP1 and SIP2.
Set Call Time Limit. This is a max duration of the call before the intercom terminates the call. Click Save. Select Phone > Audio. Enable PCMA, PCMU and G.722.
Set Priority: PCMA - 1 Highest, PCMU - 2, G.722 - 3, 9. Click Save. Select Streaming > RTSP. Click the check box RTSP Server Enabled.
Make the changes necessary based on the table below. Click Save. Select HTTP API > Services. Set Camera API to the following:
Connetion Type: Unsecure (TCP), Authentication: Basic. Click Save. Select HTTP API > Account 1. Check Account Enabled.
Create an User Name and Password. Enable all User Privileges. Click Save. Select Onvif. Enable the first Account.
Enter the NAME, and PASSWORD. Click Save. In a web browser log in to the Door Station to be configured. Select Hardware.
Select Camera > Internal Camera. Select Motion Detection Enabled.
Make any adjustments to sensitivity settings. Click Save. Select Audio Select Noise Detection Enabled.
Make any adjustments to sensitivity settings. Click Save. Select Buttons. Disable the Quick Dial Buttons by clicking the x. Click Save.

Savant Settings

  RacePoint Blueprint

To add a 2N Door Station to a configuration there is one profile that works for all Savant supported 2N IP Intercom models. In an open Blueprint configuration do the following. Click Show Library. In the Search bar type 2N.

Select the 2N Helios Door Station and drag it into a Shared Equipment zone. Name the Device.
Place the Door Station in the layout window. Select the Door Station. Make the Control connection (Ethernet). Click Generate Services. Go to Tools > Settings > Security Camera... Enter IP Address. Select Phone > Calls. Set Incoming Calls to Automatic for both SIP1 and SIP2.
Enter User Login and Password. The HTTP API/ONVIF data from the Door Stations configuration must be used. Click Done. Go to Tools > Settings > Entry... Enter the Serial Number of the Door Station.
Set the Ring Duration. Click Done. Go to Tools > Settings > Entry Event Recording... Enable the Events that are desired. Click Done.
After the Door Station has been placed in Blueprint with a control connection and services have been generated, custom buttons can be added to the Entry Service Screen in the Savant Pro App. In the example below, it will add a button to turn on a flood light that will be turned off by a timed trigger. In an open Blueprint configuration do the following:
Navigate to Tools > Settings > Entry.... Click Buttons.
Click the + icon.
Select Add Button. Select the New Button.
Name the Button. Select the Zone. Select the Service. Set Press Command. Click Apply.
Audio Interrupt Service (AIS): This service is most commonly used with a doorbell to play an audio file throughout the home. This section shows the basics of using a system state from a 2N Door Station to create a AIS doorbell. For more detailed information on creating an AIS trigger see the Audio Interrupt Service (AIS) Configuration for Doorbells on the Savant Customer Community. In an open Blueprint configuration do the Following: Make an audio connection from the Host to the audio distribution system. Generate Services. Click Review Triggers. Create a new trigger. The image below shows an example trigger. Select the Zone. Select the Service. Set Press Command. Click Apply.

  Savant mobile application

To receive calls from the door station when the user is away from the local network there are some additional steps that must be completed. In order for the Savant Pro App to receive calls when the app is closed a notification must be created for each user that wishes to be notified. This example, shows how to configure a notification for whenever the call from the door station is placed. Follow these steps: From the Home screen tap the icon. Tap the icon. Swipe up and select Notifications. Tap the icon. Select Entry.

Select Entry Ring.
Tap Next. Leave Where and When as Anywhere and Anytime. Select Send Notification. Tap Done.

Version SIS-5000

2N IP Intercom Settings

  Requirements for 2N IP Intercom

2N IP intercom with default setting is set to get IP address from DHCP. Default credentials are: Username: admin, Password: 2n. Register the 2N IP intercom to the SIS-5000: To make sure that the 2N registers on to the Savant Intercom Server, it is important that the Phone settings are completed under the Services section. From the 2N Home screen, select the Services title. Make sure that Phone is selected from the options on the left, and that SIP 1 is the currently selected tab. Complete the fields by referencing the table below. Click on the Apply button.

Verify Registration: It is important to check that 2N IP intercom is registred on the Savant Intercom Server. After completing procedure above, the registration status should be confirmed by both 2N IP intercom and the Savant Intercom Server. In 2N IP intercom Home screen you see Status, you should see that SIP 1 is REGISTRED. On the side of Savant Intercom server log in and from the Overview tab, locate the 2N device in the Devices section. Ensure that under the Reg Status column, the 2N is listed as OK.

Configure the 2N Camera: The 2N camera will appear on the TrueControl II UI page as long as the URL is configured on the Generic Door Entry Profile under Video Support as described previously. If the camera shows but only presents a still image, follow the steps below. On the 2N web interface, select the purple Services tile. Select Streaming from the menu on the left and select the JPEG tab. Ensure that the checkbox next to Snapshot Download Enabled is checked. Click Apply.

Savant Settings

  Connection diagram of integrating 2N IP intercom

  RacePoint Blueprint

From the RacePoint Blueprint toolbar, click Show Library to open the Components library. From the All Components library, enter Intercom into the search bar.

Select and drag the Savant Intercom Server into a Global Zone, In the window that appears, accept either default unique name automatically populated or enter a name that describes the Intercom Server and click Create. Select and drag the Intercom Server component into the configuration window. Double click the Intercom Server just created to open component inspector. Complete the fields in Inspector as is outlined below. Connect the Ethernet port of the Savant Intercom Server to a port on a Generic NetworkSwich profile.
 
Add Door/Gate Entry Station into Blueprint (2N IP intercom): Add Generic Door Entry System - In the Racepoint Blueprint configuration tool open the Components  library from toolbar by clicking Show Library . Enter door  into the search bar.
 
Drag the  Generic Door Entry System  to one of the zones and accept the default or enter name for Door/Gate Entry station. In this procedure 2N IP intercom was entered. Click  Create. Drag the component into the configuration window. Double click the Door Entry System to open the  Inspector. Selecet  Telephony from the  Show: drop-down menu. Highlight the  Registration line by selecting it.
Configure Video Support: For video Support highlight the  Video Support  line in the Inspector and check Enabled checbox.

 

  Savant configurator

Savant configurator is web-based graphical user interface and it is displayed in a web browser. It is connects directly into the SIS-5000 Intercom Server. To access this tool, one of three methods can be used. In all three cases login window will appear, default credentials are: Username: admin, Password: savant.

Connect Through System Monitor

The Savant System Monitor scans the local network and will find the Intercom Server. Once found, the Savant Configurator can be launched from system Monitor.

  1. Open System Monitor through Savant Application Manager.
  2. Scroll through the list of devices and find the Intercom Server. The server can be found through either:
    • IP Address assigned to the Intercom Server
    • The Device Type column in System Monitor lists the Intercom Server as a Phone System

  3. Once the Intercom Server is found, double click it and the Savant configurator will open a login screen through a web browser.

Connect Through Bonjour on Safari

Apple’s Bonjour Zero Configuration Networking Standard can be used to discover the Intercom Server.

  1. Open the Apple Safari web browser.
  2. If the Bonjour dropdown does not appear in the Favourites bar, enable it from the Advanced tab when in Safari Preferences.
  3. Select intercom from the Bonjour drop-down menu.

Enter IP Address into Browser

If you know the IP address of the Intercom Server, type the address into a web browser.

Configure the 2N IP intercom using Savant Configurator

The 2N Door Entry station must first be added as a device. Refer to instructions below to register the 2N Door Entry station. Log in to the Savant Configurator and do following:

  1. Select the Device tab to open the Devices page.
  2. Select Add Device.

  1. Click Add & Exit when complete.
  2. Click the Devices tab and verify the device has been aded.

Configure a Call Group for the 2N IP intercom

  1. Select the Call Groups tab.
  2. Select Add Group and the Add Call Group page will open.
  3. Edit the Add Call Group page using the table below.

  4. Click Save Group to save the Call Group just created. Verify the group was created.

Add Members to the 2N Call Group

  1. From the Call Groups page, select View Groups from the Call Groups side bar.
  2. Select the group just created by clicking the radio button associated with the group.
  3. Click Edit Members.
  4. Move the desired endpoints from the Available Devices table to the Group Members table by selecting each endpoint and click the << or >> arrow. These will be the devices the 2N station will call. When you finish editing click Save.

Add an Extension to the Door Entry Call Group

Each Call Group needs to have an extension associated with it. This is the number that the 2N panel will call when the button at the gate is pressed.

  1. Click the Extensions tab.
  2. In the Extensions window, click the Add Extension button and fill the Add Extension window. Refer to the table below.

  3. Click Add New Ext.
  4. Verify the extension is now in the Extensions Table with the correct information.

 

Required licenses

  • Enhanced Video
  • Enhanced Integration

Used Symbols

(tick) - Compatible

(warning) - Work with limitation

(error) - Incompatible