4.3 Záznamy o provozu - LOG

Aktuální LOG záznamy naleznete v sekci Gateway, okně Gateway control – LOG file, nebo pomocí AT&L AT příkazu v případě Telnet relace. Následující seznam LOG stavů je univerzální a některé typy záznamů nemusí 2N® VoiceBlue Next obsahovat:

Type

Text

Description

POWER

[Power on]

System switched on

[Power off]

System switched off

[Warm boot]

Restart of system, unknown cause

[Watchdog]

Restart of system by watchdog

[BKPT code]

CPU error: break code detected

[Stack error]

CPU error: stock integrity failure

[Divided by zero]

CPU error: dividing by zero

[RETI code]

CPU error: illegal using of instruction reti

[NMI intr]

CPU error: wrong interrupt

[VOID intr]

CPU error: wrong interrupt

[Upgrade reset]

Start of upgrade firmware procedure

[Software reset]

Reset by AT commands (at&fres…)

INIT

Eeprom

Initialisation of eeprom (configuration)

Flash

Initialisation of flash memory (firmware)

HW–ERR

(##…address of chip, RD…read value/WR…expected value)

Codec ##,RD/WR

Error in initialisation of codec on GSM,AUX board

COM2 #####,RD/WR

Error in initialisation of COM2 on AUX board

Duart #####,RD/WR

Error in initialisation of serial controller on GSM board

Hscx #####,RD/WR

Error in initialisation of HDLC controller on AUX board

Pri #####,RD/WR

Error in initialisation of PRI controller

SYSERR

User stack error!

SW error: stock integrity failure

BRDIN

#08 TYP STS

Board inserted (number of gsm board, type, status)

BRDOUT

#08 TYP STS

Board disconnected

BRDRES

#08 TYP STS

Reset the board by AT command

ALL GSM RESET CMD

Reset all GSM boards by AT command

SYSTEM RESET CMD

Reset the system by at&bsys command

L1–ERR

(reserved)

L2–ERR

Error of ISDN layer 2 by Q.921

A: unsol.RX(F)

Received packet RR,RNR,REJ with unexpected bit F=1

B: unsol.DM(F)

Received packet DM with unexpected bit F=1

C: unsol.UA(F)

Received packet UA with unexpected bit F=1

D: unsol.UA(–)

Received packet UA with unexpected bit F=0

E: unsol.DM(–)

Received packet DM with unexpected bit F=0

F: peer re–est

Received packet SABME in status OKEST

G: repeated SABME

Repeated unsuccessful send of packet SABME

H: repeated DM

Repeated unsuccessful send of packet DM

I: failed (TIMREC)

Unsuccessful breaking–up of status TIMREC

J: N(R) error

Received wrong value N(R) – numbering of packets

K: recv.FRMR

Received packet FRMR (information about error)

L: undef.frame

Received packet of unknown type

M: (I field)

Received wrong I–packet (numbered packet)

N: frame size

Received packet with wrong length

O: N201 error

Value N201 was exceeded (max length of packet)

L3–ERR

tout sts # (p##)

Error of isdn layer 3: timeout in status # on channel p##

G2–ERR

ATD/ERROR init (g##)

Error of isdn layer 2: restart of module g## after rejected command ATD by GSM network

GSM Cause 150 (g##)

Error of isdn layer 2: restart of module g## after cause 150 was received (call barred by GSM network)

G3–ERR

tout sts # (g##)

Error of isdn layer 3: timeout in status # on module g##

C4–ERR

tout sts # (p##/g##)

Error of connecting layer 4: timeout in status # on call between channel p## and GSM module g##