4.4 Settings


Press the right-hand lower button at the icon  to display the Device settings. Here set the DND mode, screen lock, device sounds and tones and display/system properties.


Do Not Disturb Mode


Enable/disable the DND mode using the left-hand lower button. With DND on, the icon  on the home page is red backlit. The device does not play the selected ringtone to signal an incoming call. The display shows the camera view if available, CLIP and Incoming call message.


Screen Lock



Enable/disable the screen lock (parental lock) using the left-hand lower button. Enter the PIN code to enable the screen lock. Enter the same PIN code to disable the screen lock.

Sounds and Tones


Press the right-hand lower button at the iconto display the Sounds and Tones. Here set the ringing/call volume and select the ringtone and door bell ringtone.


Ringing volume

Press the right-hand upper/lower button to increase/decrease the ringing volume. Press the left-hand lower button to confirm the volume level selected. The change will not be saved unless confirmed.

Call volume

Press the right-hand upper/lower button to increase/decrease the call volume. Press the left-hand lower button to confirm the call volume level selected. The change will not be saved unless confirmed.


Key beep volume


Press the right-hand upper/lower button to increase/decrease the key beep volume. Press the left-hand lower button to confirm the key beep volume level selected. The change will not be saved unless confirmed.

  

Ringtone

Press the right-hand upper/lower button to move up/down the ringtone list. Press the left-hand lower button to confirm the ringtone selected. The change will not be saved unless confirmed.


Doorbell ringtone

Press the right-hand upper/lower button to move up/down the doorbell ringtone list. Press the left-hand lower button to confirm the ringtone selected. The change will not be saved unless confirmed. 


Display



Press the right-hand lower button at the iconto display the Display section. Here set the display brightness, idle timeout and button backlight. 

Brightness

Press the right-hand upper/lower button to increase/decrease the display brightness. Press the left-hand lower button to confirm the brightness level selected. The change will not be saved unless confirmed.


Screen timeout

Set the maximum idle time (i.e. when the user does not control the device) after which the sleep mode is switched on automatically. Press the right-hand upper/lower button to move up/down the time value list. The change will not be saved unless confirmed. 


Button backlight

Press the right-hand upper/lower button to increase/decrease the button backlight. Press the left-hand lower button to confirm the backlight level selected. The change will not be saved unless confirmed.


System



Press the right-hand lower button at the iconto display the System section. Here set date and time, My2N/SIP Proxy state and language and get basic information on the device.


 Date and time 


  • Automatic date and time – enable the use of the NTP server for automatic internal time synchronization.
  • Date format – there are 3 date format options: 12.31.2019, 31.12.2019, 2019.12.31.
  • Use 24-hour time format – enable/disable the 24hour time format.
  • Set date – set the date manually unless automatic date synchronization is enabled.
  • Time zone – set the time zone for your installation site to define time shifts and summer/winter time transitions.

Caution

  •  The change will not be saved unless confirmed.

My2N/SIP Proxy state

The My2N/SIP Proxy section displays the current state of the My2N/SIP Proxy connections. 


Language

Press the right-hand upper/lower button to move up/down the language list. Choose one of the eight pre-defined languages (CZ, EN, DE, NL, FR, ES, IT, RU). The change will not be saved unless confirmed. 


About device

This section provides basic information on the device (serial number, MAC address, FVW version, IP address).

Press and hold the right-hand lower button to set the network interface port mode for auto-negotiation. The mode can only be selected if the port mode is defined automatically, refer to 3.2.5.1 Network.