Yealink SIP-T58A and SIP-T58V

Content

About

Version 58.80

Used Symbols

About

Phone web page

Yealink T58A

Yealink T58V

Default login admin
Default password admin
Video support

Yes

Version 58.80

Tested Functions

Yealink SIP-T58A/V
 2N IP Intercom
Direct Call
Audio
Video
Switch Control
Video Preview
Call Completed Elsewhere
Secure RTP (SRTP)
58.80.9.3 2.23.0.32.5 (tick) (tick) (tick) (tick) (tick) (tick) (tick)
58.80.0.40 2.23.0.32.4 (tick) (tick) (tick) (tick) (tick) (tick) (tick)
58.80.0.10

2.19.0.28.5

(tick) (tick) (tick) (tick) (error) (tick) Un-Tested

Direct Call

  Direct Call Settings

This guide shows how to setup direct calling between Yealink T58A/V and our IP Intercoms.

If you configure everything according to this guide you’ll be able to automatically see video preview from up to 99 intercoms when a call is received on the phone as well as activate switches on intercoms. Additionally you’ll be able to call every 2N IP Intercom in the same network.

IP addresses used

  • 2N IP Intercom      192.168.50.129
  • Yealink T58A         192.168.50.188

Firmware versions tested

  • 2N IP Intercom      2.23.0.32.4
  • Yealink T58A         58.80.0.40

Both devices were in factory defaults.

Intercom setup

After you log in to the intercom, go to Directory.

Add a new user.

Name the user and enter a new phone number in this format: sip:yealink’s IP/1. In my case it’s sip:192.168.50.188/1. Entering the /1 is very important to identify the intercom properly.

Delete 111 from the Phone Number (ID) field and leave it empty, then change Domain to the intercom’s IP address – in my case 192.168.50.129. This will allow you to call the intercom directly from the phone’s call log.

If you’d like the intercom to pick up calls (from the phone) automatically, change Call receiving mode (SIP1) to Automatic.

The Yealink offers an “Open Door” button function. To use this you should enter the intercom’s Switch Code into the phone’s configuration to open doors without having to enter this switch code manually. Firstly; this code has to be defined in the intercom’s configuration: Hardware>Switches>Switch#>Switch Codes or in Directory>Users>User#>User Codes.

Phone setup

Configuration of the phone is very straightforward. Pick one of the DoorPhones from the Door Phone List and set it as follows:

Device Type: 2N
Display Name: according to your preference
Phone Number: intercom’s IP
Unlock PIN: 00* Don’t forget the asterisk. This PIN has to be a valid code set in your intercom in step 6 of the intercom setup
Full Screen: Disabled
Send Audio: Enabled
Send Video: Enabled
Video Preview: Enabled
Auto Preview: Enabled

This is all that needs to be done in order to get video preview, activate switches and be able to call both ways without a SIP proxy.

Settings with PBX

  2N IP Intercom Settings

 Basic Settings / Phone book:

  1. Position enabled - set Yes
  2. Name - set the personal name for the selected telephone directory position. This parameter is optional and facilitates the telephone directory search.
  3. Phone Number - IP address of the called party in the format sip:ip_address_yealink, e.g.: sip:10.0.27.254.

  Yealink T58V settings

Yealink T58V settings:

Account / Register:

  1. Line Active - set Enabled
  2. Display Name - set the personal name for the selected 2N IP Intercom.
  3. Register name - set the selected Phone Number
  4. Server Host - IP address of the called party.

Video Preview settings

  Secure RTP (SRTP)

SRTP on Yealink T58V

To enable SRTP on your Yealink T58V go to Account and Advanced and set parameter "RTP Encryption (SRTP)" to compulsory.

SRTP on 2N IP Intercom

Go to SIP settings in Services and in Advanced settings enable recieving and transmitting of SRTP calls.

Advanced Functions

  Intercom Video Monitoring

This quick guide describes how to setup monitoring of 2N IP intercom cameras on Yealink T58A/V.

IP addresses used

2N® IP Verso        192.168.50.129
2N® IP Base           192.168.50.34
Yealink T58A         192.168.50.211

Firmware versions tested

2N IP Intercoms  2.23.0.32.4
Yealink T58A         58.80.9.3

All devices were in factory defaults.

Intercom setup

After you log in to the intercom, go to Services and then HTTP API. Locate the Camera API row and change Connection type to Unsecure (TCP) and Authentication to None.

If you’re getting poor framerate or would like to save some bandwidth, you can decrease JPEG quality in Streaming>JPEG down to 50.


Phone setup

Log in to the phone’s web interface and go to DSSKey tab. Choose one of the Line Keys, click on its Type dropdown menu and select Video Monitoring. The most important field here is Value, this is where you put the address of the intercom’s HTTP API camera stream in the following format:

http://intercom’s IP/api/camera/snapshot?width=640&height=480&fps=15

The remaining fields are Label and Extension. Label is the name which will identify the intercom’s camera on the display of the phone. Extension is not important in this scenario, but you can enter the intercom’s IP.

The following picture shows that I have assigned two intercom cameras to the phone’s DSS Keys using their respective IP addresses.

How it works

DSS Keys are accessible on the right side of the phone’s home screen.

Once you tap on them, they immediately show your intercom’s camera feed.

Used Symbols

(tick) - Verified with video

(green star) - Verified with audio only

(warning) - Work with limitation

(error) - Incompatible